Over the past few days I’ve primarily been focused on getting the strake hatch doors, latches and flanges finished up.  This involves a number of iterations of micro, flocro and flox fills, with the requisite cure times, sanding, refills and dialing in the edge seams and height/elevations to get the door tops as even with the surrounding strake surfaces as possible.  Of course, some contour-leveling sanding no doubt will be required.

In addition, I’ve been working a myriad of small divot and low spot micro fills, sanding, wet sanding, subsequent epoxy wipes, etc. on areas all over the bird: wings, winglets, flanges, fairings, D-deck, strake, nose cover, etc.

On the right strake hatch flange I filled the slight “trench” around the outer perimeter edge of the flange with flocro before then covering that with peel ply.

I did the same a bit later with the left side strake hatch flange, but no pic of it.

Here is the 1-ply carbon fiber layup on the inside of the left strake hatch door, after I razor trimmed it and pulled the peel ply.  Obviously it’s installed in place, and you can see the forward flange (right side of pic) has been trimmed as well.

I then spent a good hour+ drilling the holes in the left strake hatch door to install the double-button Hartwell latch.  Here we have an external shot of the latch (pic 1) and an internal one as well (pic 2).

And a couple requisite shots of the left strake hatch door latch from different angles.

As for how the hatch doors sit within the strakes’ top proper, the seams around the doors needs some filling.

Thus, to be able to get the door open, off and out of the edge flocro that I applied to the taped edge of the door, I only did about half the perimeter edge for each application.  I started with the aft side on the right strake door hatch.

And after the aft side cured I then flocro’d the forward side edge seam.

Here is a shot of the same thing on the left strake hatch, although I started on the forward (top of pic) side —which is complete in this pic— and am working the flocro application on the aft side half of the edge seam here.

Slowly the strake hatches, doors, latches, fit and finish work is getting completed and I’ll pick back up more on the aft nose/avionics cover and canopy final fit and finish.

Again, all in the effort to get this bird in primer and paint.

Pressing onward!

I started out the first half of the day today helping Guy William’s do a final fill on his left brake line.  Thankfully we had some knowledgeable EAA’ers working in the hangar next door to lend their expertise.  After another few rounds of filling the master cylinder and line, Guy then made a couple of high-speed taxis down the runway to get the brakes back to good… while I played airport bum visiting yet another EAA member as he worked on his Grumman Tiger.

This should be the last major help session required (hopefully) for a while now that Guy’s EZ seems to be back on its feet, so to speak.

I got back to my house early evening… out in my shop the first task I did was to trim the forward flange on the right strake storage hatch.  As I mentioned before, this forward side was quite a difficult flange layup —having to go in through the outboard strake rib— and with some difficulty getting the glass in place I had to scrap the outboard corner portion of the layup.

I’m jumping ahead here, as this is later in the evening after my corner gap fill layup cured (I used fast hardener with MGS-335 epoxy).

And here is the cured forward flange layup on the left side strake hatch.

After trimming the left strake hatch forward flange, I then spent some time figuring out exactly where I would be mounting the double-button latch.

Once I determined the latch position it allowed me to mark and trim out the hatch door’s center inside glass and foam to the underside of the top skin glass.  Clearly this will allow glass-to-“glass” (carbon fiber) strength when I layup the ply of carbon fiber over then entire inside surface of the hatch door.

Not shown are the 3 plies of BID I laid up in the hatch door’s latch depression first to get the thickness dialed in to 1/8″ (0.125″), again the depth of the buttons on the left side strake door latch.  I then laid up the single ply of carbon fiber over the inside of the left strake hatch door, minus the cutout for the hinge plate.  And of course I peel plied the inside of the latch install depression.

I then left the left strake hatch door layup to cure overnight.  Tomorrow, I plan on getting a good chunk of these of these strake storage hatch doors knocked out.  Again, all in the effort to get the bird prepped for primer and paint.

This post covers the past 2 days.

First I shaped one side of the right strake hatch door hinge spacer for a better contour flow of the top side of the door in relation to the strake surface.

I then taped up the aft side of the inside right strake hatch door (pic 1), wetted out peel ply along the edge of the inside door and then installed the door and weighed it down (pic 2).

With the taped and peel plied door (aft side) in place, I then laid up a 4-ply BID tape that will be the aft side flange when it cures.

After cleaning up the inboard glassed edge of the left strake door (pic 1), I then did pretty much the same thing with taping the edge, pre-wetting out strips of peel ply along the door in prep of the aft side flange layup (pic 2).

Which I did next (sorry, no internal pic).  Here’s the the left strake hatch door the following day when I removed the weight that secured it in place.

Here we have the left strake hatch door removed, and the cured, pre-trimmed aft side flange layup (peel ply pulled).

And a shot of it after it was trimmed and cleaned up.

Here we have the same thing on the right side, pre-trimmed cured aft flange layup (pic 1) and then a shot of the cured front side flange layup later in the day (pic 2)… this forward side was by far the most difficult flange layup I did on these strake hatches.

Since I kept the original strake skin piece on the left side as my door, I made a decision last night to keep the perimeter edge of the door the same stock thickness as the skin.  This made laying up the forward side flange significantly easier since it was simply laid up on the bottom side of the pre-existing perimeter strake-side skin.

I made a cardboard template of the forward strake-side overhang to create what I would need for a flange, then used the template to cut 4 plies of BID.  I then prepregged the BID (pic 1), and wet it out.  As well as again taping up the forward edge of the inside door and adding wetted out peel ply (pic 2).

This time however I was completely able to layup the flange from the hatch opening vs. having to snake my arm inside via the outboard rib.

Once the left strake forward flange BID was laid up, I then mounted the strake hatch door…

Closed it up and then added peel ply to the underside of the flange layup.

I’ll also note that my double-button Hartwell latch (left side of pic) that I ordered off of eBay arrived this afternoon.  While the button diameters are the same, the thickness of the buttons are different: the new buttons on the latch for the left hatch door are 1/8″ thick while the buttons for the right side strake hatch are 0.08″ thick (right side of pic).

I’ll continue to work what I can tomorrow to get this bird ready for primer and paint.

Pressing forward!

I started out today mixing up some micro, with West 410 added, to do a few small micro touchups/fills.  First off was the top middle underside edge of the left sidewall opening for the canopy latch handle.  When I recently reinstalled the handle it was really tight, so in sanding the perimeter of the opening I sanded a hair to much in the top middle, which was visible when the handle was installed.

Thus the micro to clean that back up.

Also on the right wheel pant I have a depression on the aft side of the seam with the front wheel pant.  So I added a bit of micro there to even the seam up.

And some micro on the aft end of the right winglet intersection fairing… after it cures I’ll sand it and epoxy wipe it (and the other micro’d spots).

Over the last day and into today I really racked my brain in figuring out how I was going to attach the strake hatch doors to the spring loaded hinges.

On the left side I made the decision to go with two 10-32 Clickbonds, that are a bit wider and thicker than my normal Cozy-Girl/Infinity Aerospace Clickbonds.

I placed the Clickbonds into the drilled 3/16″ holes and marked their edges (pic 1) before then removing the top glass and internal foam to reveal the interior glass skin (pic 2).  I also then ground off an edge of the aft Clickbond and drilled flox-grip holes into the Clickbond flanges.

And quickly ensured the Clickbonds fit into the openings I had just made.

After cleaning up the interfacing glass, I then added a couple of plies into the bottom of the holes before slathering the Clickbonds up with flox and inserting them into the holes. I then added 3 more plies of glass over top of the Clickbonds and under the edges of the holes.  I then used up all the flox in my cup by putting it around the perimeter of each hole (pic 1).  After that, I mixed up some micro to fill the remainder of the holes just slightly proud of the hatch door top surface (pic 2).

I then spent another good hour carefully spacing, placing and drilling out the holes for the right strake hatch door’s double button latch.  Here we have it initially in the closed position (pic 1) and the open position (pic 2).

I’ll note that I added a 3rd mounting screw in the center offset a bit higher to better secure the position of the door on the hinge spacer.

And a close up of the right strake hatch door’s double button latch:

I had to wait awhile before I could close the right strake hatch door since I had added 3 stepped plies of BID on the inboard edge of the right strake compartment.  Note the flush latch buttons on the surface of the strake hatch door.

A bit later I pulled the right strake hatch layup’s peel ply and trimmed the glass, at which point I was then able to test the strake hatch door by latching it in the closed position… a couple of shots here:

I also did some edge layups on both the left strake’s door and compartment inboard edges.

And tested the fit of the left strake hatch door after the layups had cured and were cleaned up.

Tomorrow I’ll press forward with these strake hatches and as much on the rest of the bird as possible.

I started out today trimming the cured carbon fiber 2-ply layup on the interior side of the right strake hatch door.  Clearly I pulled the bits of peel ply off as well.

I then pulled peel ply, razor trimmed and sanded the edges of the edge ply of BID I laid up on the left strake storage compartment opening.

And did the same thing on the right side as well.

Using my painters tape and super glue trick, I reattached the left strake storage hatch door to the hinge, and after ensuring the placement and geometry was correct, I drilled out two (2) 3/16″ holes through the hatch door and the underlying hinge flange.

On the right side I verified the size and shape of the hatch door, and also glued the hinge to the door.

I was pleased that my geometry, and thus clearance, held on the right strake hatch door.

After one final bit of gently coercing it into its final position . . .

I then drilled my hinge mounting bolt holes on the right strake hatch door.

Here are the bolts attaching the doors in place on each side.

I then wrote out some thoughts on tape for each side for how to finalizing the fit and install of each door on each side.

This was another long day of figuring things out on these doors, dialing stuff and trying not to miss of the important minutia details.  It was late and I was very ready when I called it a night.

Pressing forward!

Today I started by first cleaning up the outboard edge of the right strake hatch where I added back in the 1/4″ piece I removed to create the original hinge notch.  I then recut the outside edge at an angle on the cut line I had made.

In addition I made a notch midpoint on the inboard edge for the latch striker in prep for when I get my double-button latch installed.  I also cut narrow channels along the top and bottom of the edge foam for “flox” corners.

I then laid up a single ply of BID around the majority of the right strake hatch opening on the exposed foam.  I then peel plied the layup (sorry for the slightly fuzzy pic).

I then did the same thing over on the left strake hatch foam edges.

With my West epoxy wipes fully cured on the center bottom aft area of the right wing, I finished sanding that down with 120 grit dry paper, followed by wet sanding it with 150 grit.  That finishes off my shenanigans on the bottom of the right wing.

By early evening my right strake hatch perimeter foam edge layup had cured to the point where I could pull the peel ply and razor trim the edges.

I then turned my focus onto the right strake hatch door inside layups.  After measuring the double-button Hartwell latch buttons I determined that the 2 plies of carbon fiber that I had planned on using as the overall cover on the interior side of the hatch door would be about perfect for the two buttons to be even with the external surface.

I determined first where the hinge spacer (to mimic the original thickness of the top strake skin) would get mounted, and added 4 plies of carbon at that position to just about be even with the added reinforcement ply of Lantor Soric material (white with hex pattern).

I then wet out the Lantor Soric reinforcement material and the 4 plies of carbon fiber for the hinge spacer, before then laying up the 2 overlaying plies of carbon fiber that make up the interior surface of the right strake hatch door.  With these 2 plies that means that anywhere on the door (mainly the perimeter edge) there is, at a minimum, 5 plies of carbon fiber (approximately 0.075″ thick).

I got a little cheeky with this hatch door and decided to leave the exposed areas of the carbon fiber “raw” and only peel plied the hinge spacer and Hartwell latch base areas.

There was a lot of configuring, scheming, designing and planning for me today on exactly how I was going to get these strake hatch doors —both sides— installed and operational.  It was a long day, and fairly late, and I was very ready to call it a night.

Pressing forward!