Today I finished the current build of the Left wing.  I placed the wing on the table bottom up. I knocked the jigs off the wings & cleaned up the bondo.

I took the wing outside & placed on the fold out work table, and then sanded all the bondo off the wing.

After I finished sanding the bondo off the wing & then cleaned off the wing (the rain helped with that!).  I then stored the wing in my environmentally controlled storage facility (ha! yes, my dining room . . .)

Now, let me talk a little bit about some housekeeping items.  Literally.  Of course in the pic above, it’s a bit messy.  Well, since I’m on quite the accelerated schedule–to be able to use all the epoxy I bought en mass–I had to choose between glassin’ & sandin’ versus keeping everything else ship-shape.  Essentially, it comes down to my prioritizing the build over pretty much everything else for a few months.

The other item is an issue for the locale in which I am building: trash.  Building this airplane, especially since it’s composite, produces A LOT of trash.  Unfortunately for a plane builder, Germany is incredibly strict about its trash.  Germany has you identify trash into five (5) different categories.  Their curbside trash bins are SMALL here and they only pick up each kind of trash about every other week.  Thus, I have a lot of build trash that piles up, and not much place to put it.  So I get what I can out (often, if the trash isn’t sorted just right, they won’t touch it) and then continue to build.  Eventually, all the trash will get out since I will stop building in mid-October for at least 6 months.  Luckily, fiberglass & used peel ply doesn’t rot!

Ok, back to airplane building!

I lined up the troops one last time for some photos after their long hard slog.  Although not an exact perfect fit, I was very impressed with how well the wing jigs worked.  Brilliant idea & brilliant design in my opinion.

Afterwards, I started assembling the jig for the Centersection Spar.  I know many may be aghast at my co-mingling of different types of wood, but I had it on hand and it will all get trashed (again, at some point) eventually.  I actually shipped the long pieces of particle board here from the States specifically for this jig.

The CS Spar gets built on this jig as if the airplane were flying straight up into the air.  The backboard is actually the top.  The shelf that is level in the middle & curves downward on each end is the back of the CS spar.

Since foam gets micro’d on the surface of the shelf… and we prefer NOT to leave any foam chunks of our CS spar left attached to the wood, I covered the entire shelf assembly with duct tape (maybe the differences in wood types was getting to me a little as well).

I then took inventory of the foam & ensured it was in good shape/undamaged.

You’ll notice (if you’re a builder) that I’m using the slightly denser 3# blue PVC foam vs the 2# polyurethane.  Both are fuel resistant, unlike wing foam which dissolves rapidly in fuel & other hydrocarbon-type liquids.  Polyurethane is much easier to shape, but the dust is horrible and the chance of delaminations are much higher on the polyurethane.  I generally use wood working tools on the foam anyway, so the blue should be ok to work with.

I started by cutting the 3 large front pieces (on the jig, the front is situated on top).

Once I got the front pieces cut, I cut the identical back pieces (which are on the bottom shelf of the jig as it gets built).  The pics below have both the front & back pieces, they’re just staggered.

Then I began to cut the top & bottom blue foam pieces (the sides as it’s built).

After cutting the center top & bottom (side) pieces, I called it a night.

Today I finalized the prep for glassing the BL 55.5 wing jut out.  I wasn’t happy with the quality of the corners near the wing bolt extrusion area & near that inside at the shear web glass-to-foam junction.  So I sanded down those areas… and you could tell I was serious because I broke out the Perma-Grit tools!

After I smoothed out the surfaces to be glassed as best possible, I wanted to get the antenna cable out of the way so I didn’t have to contend with it like I did on the Right wing. I ran a long aluminum tube thru the wing cabling channel, attached some string & the antenna cable to the tube and then pulled it all back far enough inside the channel that I could layup the BL 55.5 rib glass without messing about with the antenna cable.

I cut & laid up 2 each 3″ x 30″ UNI strips over the extrusion & along the edge of the wing bolt access hole in the infamous “V” pattern.

I put a thin layer of flox over the irregular surface just Outboard of the extrusion, between it and the foam.  I then filleted the foam/glass corners with dry micro & squeegeed micro- slurry onto foam field.

I pre-pregged the 3-ply BID setup for the BL 55.5 inset rib & laid it up.  I overlapped it onto the extrusion area as well.

While the BL 55.5 inset rib was curing, I cut about half of the 1/4″ plywood that I had used for the fuselage bottom “sled” to use for jigs & templates for the next build, Chapter 14 – Center Section (CS) Spar, and a few other chapters as well.  I used the 3M 77 spray glue to tack the tracings onto the plywood, and then took the wood to the base wood shop to cut out the jigs & templates.

After returning home, I knife trimmed the 3-ply BID on the edges of the BL 55.5 jut out inset rib.

 Chapter 14 — Center Section Spar

I mocked up & then cut the wood for the CS spar jig back piece and the front “shelf” pieces.  Once I got them cut to size, I mocked it up again to ensure the measurements were correct.

Today I bondo’d the wing incident angle board to the top of the wing.

Since it’s only open a few days a week, I went to the wood shop on base to cut the shelves A, B & C for the Center Section (CS) Spar jig.

The CS spar is akin to a big beam that goes through the fuselage and sticks “straight” out each side of the fuselage at the aft end (where the rear square notches are in the fuselage).  The CS spar is what the wings bolt to (the “notch” in the wing above wraps around the end and aft side of the CS spar) via the aluminum extrusions.  It extends out away from the fuselage and ends at where you see the blue foam in the pic above, and is about as wide front-to-back, as from the front side of the shear web to front edge of the grey duct tape in the pic above.  It’s height is the same as the wing’s thickness. Essentially, it’s about a 10 ft long square box, about 6″ wide & 8″ high.

I took the angle brackets off the individual jigs & rotated the wing LE edge up on the table.  I then marked & cut the bottom glass of the BL 55.5 jut out.

I then laid the wing down flat again with the wing top up & routered out the BL 55.5 jut out are to 0.7″ deep.

I then stood the wing assembly back up & made some final preps for glassing the BL 55.5 rib tomorrow.

Today I removed the peel ply from the Outboard extrusion/wing bolt access area.

I removed the taped foam shelf from the BL 55.5 wing front jut out.

I then cut the glass straight at the Inboard & Outboard wing ends.

I then grabbed the Right wing from my storage area (yeah, you know…!) & took it out to the yard to measure all the critical dimensions.  I measured the length of the LE & the spar cap to BL 55.5 jut out measurement.  I also measured the chord at the wing ends.

I cut the top side of BL 55.5 jut out edge.

I then cut the TE at the same distance from the LE as the Right wing.

I cleaned up the shop & put the jig tops back on, and then measured the incident angles.

I started out today by vacuuming the entire top of the wing.

I also refilled my slow hardener bottles & restocked my blue glove supply.

I used a 50:50 slow/fast for the thick micro on the deep fill areas.  I used wet flox on the TE & 70:30 micro/flox on the LE.  I used 80:20 slow/fast microslurry for the foam fields.

My buddy Kevin helped me by working the epoxy station, and he also helped layup some of the glass as well.

After I got the foam all micro’d, I laid up the wing UNI glass that I had pre-cut.

I peel plied the Outboard extrusion area “V” that borders each side of the wing bolt access hole.  I also peel plied the front face of the extrusion (LWA3).

I laid up the 14″, 10″, 6″ plies of UNI over the Inboard extrusion/wing bolt hardpoint & overlapping up onto the wing (just like the Right wing).

I laid up the triangular ply of BID reinforcement on Outboard end of the wing & peel plied it.

I clamped & clothes-pinned an aluminum L-bracket–lined with duct tape–to the TE to keep it as straight as possible as it cures.

I trimmed the excess glass from around the edges & since the weather had turned much cooler, I turned on 2 heaters to keep the shop temp above 70° F.

I came back to check the layup about an hour later.  I had a couple of quarter sized bubbles that had developed right at the front edge of the spar cap.  I worked those out & re-checked the entire wing layup.  Everything looked good!

Well, I finally finished removing the peel ply from the TE.  I then finished cleaning it up.

I sanded most of the Inboard spar cap area, including around the aluminum wing bolt extrusions.  Specifically, there’s a 1″ strip of glass between the Outboard extrusion & the side of the front of wing jut-out (BL 55.5) that was pretty rough & needed some tough love. I sanded it down & got it fairly smoothed out in that 1″ strip.  It needs to be smooth since the rib that gets glassed into the front of wing BL 55.5 jut-out will overlap onto this surface. I also cleaned up the aluminum extrusion faces & the wing bolt access overhang piece (W18).

I installed the NAV2 VOR antenna by running the cable into the foam & down into the wing wiring channel.

Again, I formed & taped an extension for the BL 55.5 front of wing jut-out (where the blue tape strip is in the pic above) to be installed and will allow the glass to overhang straight. (both of my Inboard FC4 pieces were rounded over just a bit for about 4″, so I just want to the glass to come straight out and not follow the roundover… which is only about .1-.2″ deep)

I tacked on the 1″ x 65″ peel ply at the aileron junction (again, on the wing side).

The final large UNI layup on the wing is 1 ply of UNI that goes from the Inboard side straight out to the tip of the wing.  This starts above the aileron & follows the top edge of the aileron at the aft side of this layup.  So, I marked a spot at 5.9″ from the TE at BL 55.5 & put a spot at 4.35″ up from the TE at BL 106.25 to mark the aft UNI edge of this layup.  Now, there are a few other smaller layups that get glassed, but this is the last really big one.

I’m trying to get the wing prepped for the last major wing layup remaining: skinning the left wing’s upper surface.

Today I spent over 1-1/2 hours removing peel ply from the TE, and still had 18″ left to remove.

I then took the tape off the baggage pod threaded mounts.  They came out good.

I routered the Nylaflow rudder cable conduit channel using the Dremel tool.  I then installed the Nylaflow & dry micro’d it into place.  Of course I held the conduit in place with toothpicks.

In the following pics you can see the damage & repair of the split at the FC2/FC3 seam (during the shear web layup & attaching the nose of the wing).

I fabricated the NAV2 wing VOR antenna & mocked it up.

I wasn’t happy with the Inboard wing bolt aluminum extrusion, so I scuffed it up & re-rounded the edge, and then hit it with some primer since I had some shiny aluminum showing.  I’ll scuff up the primered surface & clean it off before glassing.

Today I started out by using the “Fein” saw to trim the spar cap glass overhanging the end of the wing at each end.

I then sanded the bondo off the spar cap dam area & rounded the corner just a bit.

After getting the bondo off & the dam area cleaned up, I floxed in the two upper baggage pod threaded inserts on the front of the wing.  I taped them in place so that the flox cured nice & flush with the surface of the foam.

I sanded the entire spar cap with the orbital sander, and then used the big gun: a belt sander I had picked up for leveling out the spar caps (it cleans them up nicely… also another Randi tip!).  I then vacuumed up all the fiberglass dust.

I used the Dremel tool to remove the dead micro at the seams, junctions and spar cap edges.  After cleaning up & vacuuming again, I cut the fishtail from the TE & started removing the 1″ peel ply I had tacked (stapled) onto the TE.  I had to use the Dremel on a lot of the TE, because if you remember, a bunch of the peel ply came out after I used staples vs tacks to keep it in place.  I did manage to get a fair amount of the peel ply back under the glass while glassing, but not all of it.

I used my straight sanding board to sand the remnants of the fishtail level so the TE was flush & smooth, but I also hit some parts of the wing as well, especially the FC2/FC3 junction SNAFU area.  It looked pretty good after hitting it lightly with the sanding block.

Today I started my last spar cap that I will do on these wings!

I refurbished the epoxy runoffs/downspouts/epoxy recycling assemblies.

I also pre-cut my 3″ UNI tape lengths for laying up in the spar cap trough.

I used a baggy to apply the micro to the edges of the spar cap trough, using the cake-icing method.  I then applied epoxy, again with just a dash of flox mixed in, to the shear web surface.

I laid up the spar cap & then peel plied it.  I also did a rough knife cut on each end.

After it cured for a few hours I pulled off the protective tape & plastic.  By the time I pulled all the tape & plastic off, I was able to rip the peel ply off as well.

I also knocked the dam off.

I removed the clamps from the spar cap layup dam.

I finished hand sanding the sheer web, and then grabbed the Dremel tool and removed the dead micro, epoxy & glass from each side of the spar cap channel.

I re-vacuumed the spar cap & the entire top wing surface.

I duct taped along the edges of the spar cap channel with the ever-ubiquitous protective plastic to protect the wing foam surfaces.

I then shifted gears away from the spar cap prep, to cutting the UNI glass that would be used for the top wing skin AFTER the spar cap is layed up.   I pre-cut the UNI cloth before the spar cap layup on the bottom of this wing as well, I just didn’t get any pictures of it. This was somewhat of a departure from how I did the Right wing, with just the roll of UNI on the dispenser.  I am now a huge fan of precutting the glass.  It makes the layup go much smoother, easier and faster, and it seems to be a little less messy as well.